Boat Flooring Tools, Adhesives & Padding


Double Sided Seam Tape

Part # M-FAD0DST

Our Double-Sided Tape is perfect for marine flooring installations. It’s an aggressive, dry adhesive film that provides a ‘clean zone’ free of adhesive contamination. With some exceptions (as noted below), it must be used under all STRAIGHT seams. Exceptions include: seams to be heat welded the same day, under curve seams or decorative insets, or when patching or repairing. For all chemically welded seams, apply the tape before the underlying adhesive has cured.

Surface must be clean and dry. Dusty surfaces may need to be primed. Protect from freezing or overheating. 12 month shelf life when stored at room temperature in a dry, heated area.

Packaging: Individual rolls 2″ (51mm) wide by 60′ (18.28 m) long

Weight: .75 lbs.

PRICE: Each

Quantity:





LONTAPE – 4in x 108ft

Part # M-FLRTAP4

Lontape is a clean and easy replacement for all adhesive systems and can be used to install all of our floors. By following the instructions, application and clean-up time should be greatly reduced.

This roll is 4″ (101.6mm) wide and 36 yards, or 108 lineal feet (32.9m), long.

Possible Substrates:
Painted surfaces, Polyethylene, ABS, EPDM, Polyester, Steel, Aluminum, Glass, Foam, PVC, Polypropylene, Polycarbonate, and Concrete. (Note: Due to differing textures and properties of these substrates, Lontape may have differing adhesion levels.)

Directions:
1. New Surface: clean with 1/2 water and 1/2 isopropyl alcohol and a clean cloth.
Old Surface: remove any old flooring, paneling, wallpaper, or adhesive remaining on the surface. Clean with 1/2 water and 1/2 isopropyl alcohol and a clean cloth.

2. For ease of application, apply Lontape product to back of flooring, up to every 1 – 1.5 inches, leaving the red liner intact. To ensure a good adhesion, 100% coverage on edges and corners is recommended.

3. Align flooring product before removing liner. Gradually begin to remove red liner (backing). To reduce air bubbles, apply pressure from the center to the edges. Once the surface has been applied, using a standard floor roller to provide additional pressure will secure the bond.

4. After floor has been applied, avoid extra foot traffic and all peeling or prying of the edges for the first 12 hours.

Weight: 2 lbs.

PRICE: Each

Quantity:





LONTAPE – 6in x 108ft

Part # M-FLRTAP6

Lontape is a clean and easy replacement for all adhesive systems and can be used to install all of our floors. By following the instructions, application and clean-up time should be greatly reduced.

This roll is 6″ (152.4mm) wide and 36 yards, or 108 lineal feet (32.9m), long. (This item is not pictured. The photo shows the 4″ wide size of Lontape.)

Possible Substrates:
Painted surfaces, Polyethylene, ABS, EPDM, Polyester, Steel, Aluminum, Glass, Foam, PVC, Polypropylene, Polycarbonate, and Concrete. (Note: Due to differing textures and properties of these substrates, Lontape may have differing adhesion levels.)

Directions:
1. New Surface: clean with 1/2 water and 1/2 isopropyl alcohol and a clean cloth.
Old Surface: remove any old flooring, paneling, wallpaper, or adhesive remaining on the surface. Clean with 1/2 water and 1/2 isopropyl alcohol and a clean cloth.

2. For ease of application, apply Lontape product to back of flooring, up to every 1 – 1.5 inches, leaving the red liner intact. To ensure a good adhesion, 100% coverage on edges and corners is recommended.

3. Align flooring product before removing liner. Gradually begin to remove red liner (backing). To reduce air bubbles, apply pressure from the center to the edges. Once the surface has been applied, using a standard floor roller to provide additional pressure will secure the bond.

Weight: 3 lbs.

PRICE: Each

Quantity:





Flooring Template Material

Part # PT-2400

This material is transparent so you can see the deck underneath and easily mark any outlines, hinges, hardware, hatches, etc. It comes in a 52 inch x 50 foot (1.3m x 15.3m) roll and it’s .007 mil thick. Flooring template material is very durable but cuts easily with a good pair of scissors.

Weight: 13 lbs.

PRICE:

Quantity:





Lonsealer Seam Adhesive

Part # M-FADLNSL

Lonsealer chemically welds flooring seams or fuses the sheeting to itself. It is a fast-flash solvent supplied in a metal tube that has a ‘needle’ protruding from the nozzle.

A 4.5 oz. (.13kg) tube covers approximately 150-250 linear feet (45.7-76.2m) of seaming, depending on texture.

Weight: 1 lb.

PRICE: Each

Quantity:





Flooring Epoxy Adhesive – Gallon (3.8 liters)

Part # M-FADEPOX

This two-component epoxy adhesive provides outstanding adhesion for high performance indoor-outdoor installation of PlasTEAK vinyl flooring over approved underlayment surfaces.

Use this epoxy for such applications as:
• Temperature extremes like saunas, cold storage, commercial kitchens, and walk-in freezers. • Locations where flooding is possible including around drains, shower areas, public bathrooms, pool/whirlpool aprons, and laundry rooms. • Locations where sheet vinyl is installed adjacent to another flooring type that cannot be heat or chemically welded to sheeting and where there will be no transition covering.

Recommended Substrates: 1) Underlayment grade plywood, fully cured concrete, 2) all nonporous surfaces including fiberglass, metal, existing well-bonded epoxy paint, 3) properly-prepared existing vinyl floors.

Epoxy Adhesive is a two-part epoxy, recommended when applying vinyl marine flooring to any areas where superior adhesion is desired. This is often used on fiberglass substrates, particularly in hot climates or other temperature extremes such as saunas or freezers. This is also recommended where flooding is possible.

This Epoxy Adhesive consists of two parts labeled PART A and PART B that, when mixed together, equal a gallon. One gallon covers approx. 110 square feet. Work time is up to 40 minutes at 70 degrees F. Normally, it takes 72 hours for this adhesive to fully cure.

Weight: 15 lbs.

PRICE: Each

Quantity:





Flooring Adhesive – Quart (946 ml)

Part # M-FADTHQT

This adhesive is a premium quality, white, acrylic adhesive. Called “transitional” because it transitions from having outstanding green grab to firm curing with little residual grab. It is suitable for installing all of our sheet vinyl products and for use on all grade levels. This flooring glue is recommended for use during the installation of our Marine Flooring. Use a 1/32 inch trowel for best results. One quart covers approx. 45-50 square feet (4 to 4.6 square meters).

Weight: 3 lbs.

PRICE: Each

Quantity:





Flooring Adhesive – Gallon (3.8 Liters)

Part # M-FADTHGL

This adhesive is a premium quality, white, acrylic adhesive. Called “transitional” because it transitions from having outstanding green grab to firm curing with little residual grab. It is suitable for installing all of our sheet vinyl products and for use on all grade levels. This flooring glue is recommended for use during the installation of our Marine Flooring. Use a 1/32 inch trowel for best results. One gallon covers approx. 200 square feet (18.6 square meters).

Weight: 9 lbs.

PRICE: Each

Quantity:





Seam Adhesive Kit with DVD!

Part # M-FADSMKT

This Seam Adhesive Kit includes items that are needed when an area is wider than 6′ (1.83m) and the sheet has to be seamed. The kit includes 4.5 oz. Lonsealer, a roll of Double-Sided Tape, five Curved Blades, and a DVD with video featuring very helpful seaming instructions and tips.

Lonsealer chemically welds flooring seams or fuses the sheeting to itself. It is a fast-flash solvent supplied in a metal tube that has a ‘needle’ protruding from the nozzle.

A 4.5 oz. (.13kg) tube covers approximately 150-250 linear feet (45.7-76.2m) of seaming, depending on texture.

Our Double-Sided Tape is perfect for marine flooring installations. It’s an aggressive, dry adhesive film that provides a ‘clean zone’ free of adhesive contamination. With some exceptions (as noted below), it must be used under all STRAIGHT seams. Exceptions include: seams to be heat welded the same day, under curve seams or decorative insets, or when patching or repairing. For all chemically welded seams, apply the tape before the underlying adhesive has cured.

Surface must be clean and dry. Dusty surfaces may need to be primed. Protect from freezing or overheating. 12 month shelf life when stored at room temperature in a dry, heated area.

Packaging: Individual rolls 2″ (51mm) wide by 60′ (18.28 m) long.

These Curved Blades are recommended for cutting our marine flooring during installation. You will receive a 5-Pack of Blades.

Weight: 3 lbs.

PRICE: Each

Quantity:





Hooked Utility Knife Blades – 5 Pack

Part # M-FLRTBDS

These hooked Blades are recommended for cutting our marine flooring during installation. Hooked blades make it much easier to get up under the flooring sheet when you cut.

You will receive a 5 Pack of these blades.

Weight: 1 lb.

PRICE: Each

Quantity:





Curved Utility Knife Blades – 5 Pack

Part # M-FLRTBLD

These HALF MOON Curved Blades are recommended for cutting our marine flooring during installation. Curved blades help get up under the flooring sheet and make cutting much easier.

You will receive a 5 Pack of these blades.

Weight: 1 lb.

PRICE: Each

Quantity:





Floor Roller

Part # M-FLRTRLR

This high quality floor roller is perfect for use during installation of our marine flooring. This is used to ensure that a proper bond is achieved when laying your floor. It smoothes the floor and helps to push out any air bubbles. This extends up to 27 inches (68.5cm) and the rubber roller is 7 ½ inches (19cm) wide. Can also be used for Formica.

Weight: 3 lbs.

PRICE: Each

Quantity:





Vinyl Floor Cutting Shears

Part # M-FLRTSHR

These vinyl shears are recommended for cutting our marine flooring during installation. Perfect for multi-angle cutting, these shears show angles on the base to assist in accurate cuts. We import these from the UK because we have not found any better cutting utencil in the States!

Weight: 3 lbs.

PRICE: Each

Quantity:





Adhesive Trowel

Part # M-FLRTSPR

This Adhesive Trowel is recommended for use during installation of our marine flooring. The notches are sized at 1/32 inch (.8mm).

Weight: 1 lbs.

PRICE: Each

Quantity:





PlasTEAK Floor Padding

Part # M-FLR0LS

PlasTEAK Floor Padding is used as an optional padding underlayment for our interior vinyl flooring. The padding helps give your floor a smooth appearance if you have minor irregularities. It also tends to add a more luxurious feel to your finished flooring, while adding comfort similar to carpet padding. Providing excellent indentation resistance to foot traffic, PlasTEAK Padding offers multiple benefits to most applications. It is constructed of a closed cell foam that does not support moisture retention or bacterial growth.

During installation, glue is applied to the substrate, then the padding is laid. Glue is then applied on top of the padding, then the vinyl flooring is laid. Plan to use two layers of glue.

PRODUCT INFO:
Nominal thickness: 0.200″ (5.0mm)
Roll size: 70” (1.78m) wide x 60′ (18.29m)
Weight: 2.5 lbs. per linear foot (1.13kg)
Price: $24.00 per linear foot. Sold by linear foot only.
Note: 1 ft. = 304.8mm


Weight: 2.5 lbs.

PRICE: Per Lineal Foot

Quantity: